DNETCoreGPIO 1.0.3

DNETCoreGPIO

A .NET Core app to run on the RPi. Works with both Raspian and Win10 IoT-Core unchanged. Exemplifies System.Devices.GPIO and Iot.Device.Bindings Nuget packages. Provided as Visual Studio 2022 project.

Usage

Create a .NET Console app:
Run dotnet new console

Add the library as a Nuget package
Run dotnet add package DNETCoreGPIO --version 1.0.x
NB: Use the current version, in place of 1.0.x, check at https://www.nuget.org/packages/DNETCoreGPIO/

Change the 7th line in Program.cs as below:

namespace ConsoleGPIOApp
{
	class Program
	{
		static void Main(string[] args)
		{
			DotNetCoreCoreGPIO.Program.Main(args);
		}
	}
}

Build and run the app with the required parameter.(See below)

This is based upon the GitHUb Repository: dotnet/iot<br> Whereas the samples therein (from which this is taken, and extended) use library sources in that repository, this uses the associated Nuget packages.

Parameters

Run the app with the following parameters)_

1. Led and Button press
2. Temperature with BME280 sensor ..2Do
3. Temperature and Humidity with DHTxx sensor ..2Do
4. Temperature and Humidity with DHT22 sensor using 1-Wire <
5. LED driven by Software PWM.
6. H-Bridge Motor using L293D

Whilst the above run continously or until stopped the following only do a single pass. These are used by TRIGGERcmd 11/12. Relay On/Off 14. Temperature and Humidity with DHT22 sensor using 1-Wire. Get single value and write to /tmp/temperature.txt. See TRIGGERcmd.GetTempDHTxx1Wire()
15. Temperature Pressure and Humidity with BME280. Get single values and write to /tmp/temperature.txt (Coming)

The following control the motor as in 6 but as separate commands.

20. Motor Partial off: Set Fwd and Rev to off
21. Motor Forward
22. Motor Reverse
23. Motor Enable
24. Motor Disable
25. Motor Off (Fwd=Rev=En=off)

Run

Running Led and Button

Pins:

• LED Anode to GPIO17
• Button1 to GPIO4
• Ground (LED Cathode and Button2) (to the one in between. <br>ie Pins 11 7 and 9 resectively.
• Reminder that the LED requires a current limiting resistor.

SW driven LED

As above

DHT22

See circuit diagram under Circuits .<br> Active pin is is GPIO26. I'm using a 10K pullup to that. <br>Some conversions fail, which output as dots. Doesn't work on IOT-Core.

Motor

See circuit diagram in Circuits folder, left part. <br>Pins (L293D pins in brackets):

• Enable GPIO 22 (E1) (L293D Enble 1)
• Reverse GPIO 27 (I1)
• Forward GPIO 17 (I2)

Relay

See circuit diagram in Circuits folder, right part. <br>Pins (L293D pins in brackets):

• On/Off GPIO 19 (E2) (L233D Enable 2)
• Lo (I4)
• Hi (I3)
• I4 and I3 only need to be in opposite state
• Probably want Motor disabled if is low voltage and relay is 12V coil voltage.

BME280

• See circuit diagram rpi-bmp280_i2c.png for 4 pin connections.
• If unit is more than 4 pins see BME280Sampler.Get() for extra pins.
• Also see there wrt enabling I2C on RPi and for checking.

<p> <b>On IoT-Core DO NOT RUN IN POWERSHELL. Can't get user input for Console app in Remote PowerShell.<br> Run an SSH session.</b>Or directlly on the device.<br> I also attached a LED to each output.

More on My Blog